IC697PWR710F GE Power Module

Product Description

The IC697PWR710F GE power module provides stable and reliable DC power supply for GE’s automation control system,ensuring the normal operation of the system.

feature

High efficiency:high conversion efficiency,reducing energy waste.

Wide input voltage range:Adapt to different power grid conditions.

Redundant design:supports hot swapping,provides power redundancy function,and enhances system reliability.

Protection function:It has multiple protection functions such as overvoltage,overcurrent,and overheating.

IC697PWR710F is a high-performance power module provided by GE Industrial Solutions,designed specifically for industrial automation control systems,providing stable and reliable DC power.

IC697PWR710F is a power module that is part of the series 90-70 platform and is currently part of Emerson Automation,previously produced by GE Fanuc.This power module is installed on the series 90-70 substrate and can operate at an input voltage of 120/240 VAC or 125VDC.The maximum output power is 56 watts,the output voltage is 4.90-5.25 VDC,and the nominal voltage is 5.1 VDC.It has integrated overvoltage and overcurrent limitations.

IC697PWR710F is a programmable logic controller(PLC)power module installed on 90-70 series substrates.This module provides the necessary backplane power supply to power modules installed on the same substrate.

IC697PWR710F operates when connected to an external AC or DC power source(specifically 90-264 VAC,frequency 47-63 Hz or 100-150 VDC).The maximum input power of this module at full load is 90 watts,with a peak surge of 3 amperes(typical value)at half cycle input,and a power factor greater than 0.95.Its maximum output power is 56 watts,with a nominal output voltage of 5.1 VDC and an output voltage range of 4.90-5.25 VDC.

The IC697PWR710F has integrated overvoltage and overcurrent limits,specifically 6.2 volts(typical value provided by internal electronic voltage protection)and 12 amperes(typical value provided by integrated electronic current limit).This power supply also has an AC input loss time of 21 ms and is designed to be compatible with VME standard C.1.

IC697PWR710F has a grounding terminal that can be used to improve the system’s noise resistance.Use American Wire Gauge(AWG)#12 or 3.3 mm2 wires to establish a connection to the module grounding terminal.The GND terminal of this module is designed to be connected to the rack GND terminal and then designed to be connected to the functional grounding GND.Tighten the connection to a torque of 12 inch pounds or 1.3 Newton meters,and only use copper conductors with a rated temperature of 75 degrees Celsius.

The IC697PWR710F power module is a 120 to 240 volt AC or 125 volt DC rated power module manufactured by GE Fanuc.The IC697PWR710 power module is part of the series 90-70 platform manufactured by GE Fanu.It is equipped with an active power factor correction circuit to maintain cohesive power factor,eliminating the need for oversized circuit breakers and wiring.IC697PWR710F has overvoltage protection function.When the 5-volt bus voltage rises and exceeds 6.2 volts,the electronic overvoltage protection circuit will clamp the output.This can prevent external overvoltage on the output from causing the power fuse to blow.The IC697PWR710F power module has been configured so that if an internal fault occurs in the power supply due to overvoltage,the fuse will not blow.

The IC697PWR710F power module also features overcurrent protection in the form of a 12 ampere electronic overcurrent limit.If the maximum rated current is exceeded,the output voltage will decrease.In an ideal situation,the IC697PWR710F power module will remain safe until high loads are removed or reduced,so that current overload will not cause the fuse to blow.The IC697PWR710F power module provides dual rack protection through two racks operating under different conditions.For example,the second rack only requires a 5-volt power supply,and the total power required for both racks is within the capacity range of the power supply.The IC697PWR710F power module is a plug-in module that can be installed in the leftmost slot of any standard IC697 rack or VME integrator rack.

application area

The IC697PWR710F GE power module is widely used in automation control systems in fields such as power,petroleum,chemical,water treatment,and transportation,providing stable and reliable DC power supply for various industrial equipment.